PEER-REVIEWED PUBLICATION

2026

The nonlinear mechanics of single electrospun polyurethane fibers under wet and dry conditions

A tensile test divider icon

Madariaga A, Lohr MJ, Beck JL, et al.

Soft Matter

The University of Texas at Austin

RESEARCH SUMMARY
This study characterized the nonlinear mechanical behavior of individual electrospun polyurethane fibers and examined how acute and prolonged water exposure influence their response. Single Carbothane 85A polyurethane fibers were evaluated in three hydration states: dry, submerged in water for approximately one hour during testing, and soaked in water for four days before testing. Across all conditions, repeated deformation produced three consistent behaviors: nonlinear strain stiffening, loading-unloading hysteresis, and Mullins-type mechanical damage. Experimental stiffness increased significantly with strain but did not differ significantly among hydration groups overall. However, four-day-soaked fibers consistently exhibited lower average stiffness and peak force and dissipated less energy through damage than dry or acutely submerged fibers, suggesting water-induced plasticization after prolonged exposure. Energy analysis showed that most mechanical work was recovered elastically at lower strains, while viscous and damage-related dissipation increased with deformation. Dry and submerged fibers generally dissipated more energy through damage, whereas soaked fibers showed a larger relative viscous contribution. A quasi-linear visco-hyperelastic damage model incorporating an Ogden hyperelastic term, Prony-series viscoelasticity, and strain-history-dependent damage successfully reproduced the experimental force-displacement behavior, with R² values of 0.95-0.97 for averaged datasets. Model parameters further supported hydration-dependent changes, including reduced damage and increased viscous contribution in soaked fibers. Thermogravimetric analysis confirmed greater water content after four-day soaking, while FTIR, SAXS, and WAXD measurements were unable to conclusively identify the proposed molecular reorganization mechanisms. Overall, the work provides fiber-scale mechanical data and a constitutive framework for modeling electrospun polyurethane biomaterials under physiologically relevant aqueous conditions and demonstrates that prolonged hydration can alter the balance between elastic, viscous, and damage-related deformation mechanisms.
CellScale hexagons, without text

CELLSCALE INSTRUMENT USED

MicroTester

A CellScale MicroTester G2 was used to mechanically characterize individual electrospun polyurethane fibers under dry, acutely submerged, and four-day water-soaked conditions. Single fibers were harvested onto custom 3D-printed collectors and mounted directly on the MicroTester. A 0.1016 mm diameter steel MicroTester beam was positioned near the center of each fiber, creating the study’s three-point loading configuration. Before testing, a 0.4% pre-strain was applied to ensure that the fiber was initially in tension. Dry fibers were tested in air after 24 hours of drying, submerged fibers were tested in a water bath after approximately one hour of total water exposure, and soaked fibers were immersed for four days before being tested in a water bath. All specimens underwent the same sequential cyclic loading protocol, consisting of two loading cycles each to 10%, 15%, 20%, and 30% strain. Fibers were loaded at 11 µm/s and unloaded at 22 µm/s, with each full experiment lasting approximately 30 minutes. Force and displacement were derived from the known stiffness and measured deflection of the MicroTester steel beam. These measurements revealed nonlinear strain stiffening, hysteresis, and cycle-dependent damage across all hydration states. Fiber stiffness increased strongly with strain, while prolonged water soaking shifted the response toward lower average stiffness and peak force, reduced damage-related energy dissipation, and increased the relative contribution of viscous behavior. MicroTester data were also decomposed into elastic, viscous, and damage energy components and fitted with a quasi-linear visco-hyperelastic damage model, allowing the authors to quantify hydration-dependent changes in shear modulus, strain-stiffening behavior, damage evolution, viscous modulus, and relaxation time. The MicroTester measurements therefore provided the experimental foundation for both the fiber-scale mechanical characterization and the constitutive model developed for predictive multiscale modeling of electrospun polyurethane biomaterials.
AUTHORS

Alberto Madariaga, Matthew J. Lohr, Jessica L. Beck, Sascha L. Granhold, Elizabeth Cosgriff-Hernandez, Jan N. Fuhg, Berkin Dortdivanlioglu, Manuel K. Rausch.

PUBLICATION DETAILS
JOURNAL

Soft Matter

YEAR

2026

INSTITUTIONS

The University of Texas at Austin

COUNTRIES

United States

INSTRUMENT USED

MicroTester

TESTING METHODS

Flexural and Bending TestingMicro-Mechanical TestingViscoelastic & Time-Dependent Testing

RESEARCH APPLICATIONS

Material Fatigue and DurabilityPolymers and Elastomers Testing

Related Publications:

Instrument Used:
Year:
Testing Method:
Research Application:
Country:

Contact Sales

Product of Interest:
CellScale hexagon shapes