PEER-REVIEWED PUBLICATION

2026

A Multi-Crosslinkable Methacrylated Alginate-GelMa Bioink for Drop-on-Demand Bioprinting

A tensile test divider icon

Bui T, Karakaya E, Faber J, et al.

Macromolecular Bioscience

Friedrich-Alexander-University Erlangen-Nürnberg, University of Würzburg

RESEARCH SUMMARY
This study developed a low-viscosity, multi-crosslinkable bioink based on methacrylated alginate dialdehyde (ADAMa) combined with gelatin methacryloyl (GelMa) for Drop-on-Demand bioprinting. The material was designed to support several complementary crosslinking mechanisms, including UV-initiated photopolymerization, dynamic Schiff-base formation, ionic crosslinking with calcium, and enzymatic crosslinking with microbial transglutaminase. ADAMa synthesis and functionalization were confirmed using NMR, ATR-FTIR, and gel permeation chromatography, while rheological and mechanical testing were used to determine how composition and crosslinking affected material behavior. Increasing GelMa content increased compressive stiffness, with effective compressive moduli spanning approximately 0.3 to 30 kPa across the tested formulations and crosslinking conditions. Multi-crosslinking generally increased stiffness compared with photocrosslinking alone, with ADAMa25, containing 25% ADAMa and 75% GelMa, showing particularly favorable mechanical, biological, and printing characteristics. Human BJ1 fibroblasts cultured on the materials showed increasing viability over eight days, with higher GelMa content supporting greater spreading and cell density. Drop-on-Demand printing experiments demonstrated that low-viscosity ADAMa-GelMa inks could form filaments, grids, and free-standing vertical pillars, although GelMa-rich formulations generally provided better printability and shape fidelity. Cell-laden GelMa and ADAMa25 constructs were successfully printed, and multiphoton microscopy showed cells distributed throughout the three-dimensional pillars. Overall, the study demonstrates that ADAMa-GelMa provides a mechanically tunable and biologically compatible multi-crosslinkable bioink platform that can balance the low viscosity required for droplet-based printing with sufficient post-printing mechanical stability for three-dimensional cell-laden constructs.
CellScale hexagons, without text

CELLSCALE INSTRUMENT USED

MicroTester

A CellScale MicroTester LT was used to quantify the compressive mechanical properties of ADAMa, GelMa, and mixed ADAMa-GelMa hydrogel formulations under physiologically relevant aqueous conditions. Hydrogel films were prepared at 4 w/v% polymer content in 5 mm diameter by 2 mm high silicone molds and photocrosslinked with 405 nm light for 120 seconds. Depending on the test condition, samples were subsequently crosslinked with 0.1 M CaCl2 alone or with both 0.1 M CaCl2 and 2 w/v% microbial transglutaminase. After crosslinking, the hydrogels were stored overnight in DPBS at 4 °C. For MicroTester measurements, samples were placed in a 37 °C water bath and compressed using a metal beam. Each specimen underwent four compression cycles at a strain rate of 0.005 s−1 to a maximum strain of 10%, followed by a 5-second hold, 20-second recovery period, and 5-second rest before the next cycle. The first cycle was treated as preloading and excluded from modulus calculation. Effective compressive modulus was calculated from the 2-5% strain region using the measured force, sample cross-sectional area, initial height, and displacement, with specimen diameter and height determined using the MicroTester optical system. The measurements showed that compressive modulus increased strongly with GelMa concentration and with additional crosslinking, ranging from approximately 0.3 to 30 kPa across the material system. Pure photocrosslinked ADAMa produced the lowest stiffness, whereas multi-crosslinked ADAMa25 produced among the highest measured values. Multi-crosslinked formulations containing at least 50% GelMa generally reached compressive moduli of approximately 20 kPa or greater. These MicroTester measurements provided the quantitative mechanical basis for evaluating the tradeoff between low-viscosity printability and post-crosslinking structural stability and helped identify ADAMa25 as a promising formulation for Drop-on-Demand biofabrication.
AUTHORS

Tommi Bui, Emine Karakaya, Jessica Faber, Jonas Röder, Jörg Teßmar, Julian Bauer, Oliver Friedrich, Silvia Budday, Aldo R. Boccaccini, Rainer Detsch.

PUBLICATION DETAILS
JOURNAL

Macromolecular Bioscience

YEAR

2026

INSTITUTIONS

Friedrich-Alexander-University Erlangen-Nürnberg, University of Würzburg

COUNTRIES

Germany

INSTRUMENT USED

MicroTester

TESTING METHODS

Compression TestingHydrated and Temperature Controlled TestingMicro-Mechanical Testing

RESEARCH APPLICATIONS

3D Bioprinting & Bioink Materials TestingCell Laden HydrogelsHydrogel Mechanical Testing

Related Publications:

Instrument Used:
Year:
Testing Method:
Research Application:
Country:

Cell-generated forces recapitulate geometry-defined deformation modes in auxetic and non-auxetic micro-architected scaffolds

Parlanis A, Farsari M, Ranella A

Cell Reports Physical Science

MicroTester

Compression TestingMicro-Mechanical Testing

Scaffold Mechanical TestingStem Cell Mechanobiology

2026

A Multi-Crosslinkable Methacrylated Alginate-GelMa Bioink for Drop-on-Demand Bioprinting

Bui T, Karakaya E, Faber J, et al.

Macromolecular Bioscience

MicroTester

Compression TestingHydrated and Temperature Controlled TestingMicro-Mechanical Testing

3D Bioprinting & Bioink Materials TestingCell Laden HydrogelsHydrogel Mechanical Testing

2026

The nonlinear mechanics of single electrospun polyurethane fibers under wet and dry conditions

Madariaga A, Lohr MJ, Beck JL, et al.

Soft Matter

MicroTester

Flexural and Bending TestingMicro-Mechanical TestingViscoelastic & Time-Dependent Testing

Material Fatigue and DurabilityPolymers and Elastomers Testing

2026

Contact Sales

Product of Interest:
CellScale hexagon shapes