PEER-REVIEWED PUBLICATION

2026

Preparation of hydrophobic semi-transparent regenerated cellulose composite membranes reinforced by low-cost ground calcium carbonate

A tensile test divider icon

Zhang Y, Jiang X, Yuan M, et al.

Food Packaging and Shelf Life

Tianjin University of Technology

RESEARCH SUMMARY
This study developed low-cost, biodegradable regenerated cellulose composite membranes for sustainable food packaging by combining ground calcium carbonate reinforcement, glycerol-PVA plasticization, and stearic-acid surface modification. Hardwood-pulp cellulose was dissolved in a NaOH/urea aqueous system, regenerated into films, and reinforced with 5-20 wt.% ground calcium carbonate. Moderate GCC incorporation improved film mechanics through hydrogen bonding and interfacial stress transfer between hydroxyl-rich calcium carbonate particles and cellulose chains, while excessive filler loading caused particle aggregation and mechanical defects. Pure regenerated cellulose exhibited a tensile strength of 27.40 ± 0.10 MPa and elongation at break of 13.30 ± 1.45%. Increasing GCC content to 15 wt.% raised tensile strength to 32.34 ± 0.02 MPa while maintaining 22.36 ± 2.56% elongation. Combining 15 wt.% GCC with glycerol and PVA produced the strongest and most extensible formulation, GPC/Ca15, with tensile strength of 41.61 ± 0.16 MPa and elongation at break of 99.08 ± 4.67%. Subsequent stearic-acid treatment retained high tensile strength at 40.63 ± 0.19 MPa while reducing elongation to 44.05 ± 3.41% and increasing the water contact angle to 108°, producing a hydrophobic surface. The optimized membrane also showed low water solubility of 1.46%, water-vapor permeability of 4.33 g·mm/(m²·d·kPa), and approximately 60% visible-light transmittance. Structural characterization indicated that 15 wt.% GCC produced the most uniform filler dispersion and strongest filler-matrix interaction, while higher loading caused agglomeration. Overall, the work demonstrates that regenerated cellulose films can be mechanically reinforced and rendered hydrophobic using inexpensive, commercially available components, yielding semi-transparent biodegradable membranes with mechanical and moisture-barrier properties suitable for sustainable food-packaging applications.
CellScale hexagons, without text

CELLSCALE INSTRUMENT USED

UniVert

A CellScale UniVert mechanical testing system was used to perform uniaxial tensile testing on regenerated cellulose and GCC-reinforced composite membranes. Dumbbell-shaped specimens measuring 10 × 70 mm were prepared from each film formulation. Average specimen thickness was determined from measurements at three separate locations before testing. The UniVert measured force and elongation to determine tensile strength and elongation at break. Tensile strength was calculated from maximum fracture force divided by specimen cross-sectional area, while elongation at break was calculated from the change in specimen length relative to initial gauge length. The testing showed that pure regenerated cellulose had a tensile strength of 27.40 ± 0.10 MPa and elongation at break of 13.30 ± 1.45%. Adding GCC progressively improved strength up to an optimum at 15 wt.%, where RC/Ca15 reached 32.34 ± 0.02 MPa and 22.36 ± 2.56% elongation. At 20 wt.% GCC, strength remained similar but elongation fell sharply to 12.40 ± 3.76%, consistent with particle agglomeration and stress-concentration defects observed by SEM. Further modification of the 15 wt.% GCC formulation with glycerol and PVA produced GPC/Ca15, which reached 41.61 ± 0.16 MPa tensile strength and 99.08 ± 4.67% elongation. Stearic-acid surface modification retained a high tensile strength of 40.63 ± 0.19 MPa but reduced elongation to 44.05 ± 3.41%. These UniVert measurements provided the primary quantitative evidence that GCC reinforcement, glycerol-PVA plasticization, and stearic-acid surface treatment can be balanced to tune strength and ductility in regenerated cellulose packaging membranes.
AUTHORS

Yi Zhang, Xinying Jiang, Miao Yuan, Fei Xie, Xianshun Zeng, Wenjiang Li.

PUBLICATION DETAILS
JOURNAL

Food Packaging and Shelf Life

YEAR

2026

INSTITUTIONS

Tianjin University of Technology

COUNTRIES

China

INSTRUMENT USED

UniVert

TESTING METHODS

Tensile Testing

RESEARCH APPLICATIONS

Membranes and Thin Films MechanicsPolymers and Elastomers Testing

Related Publications:

Instrument Used:
Year:
Testing Method:
Research Application:
Country:

Reduced cortical bone strength and altered osteocyte canaliculi despite preserved bone mass in male Becn1+/− mice

Pei Q, Qin X, He Y, et al.

Bone

UniVert

Flexural and Bending Testing

Bone Tissue Engineering & Mechanics

2027

Preparation of hydrophobic semi-transparent regenerated cellulose composite membranes reinforced by low-cost ground calcium carbonate

Zhang Y, Jiang X, Yuan M, et al.

Food Packaging and Shelf Life

UniVert

Tensile Testing

Membranes and Thin Films MechanicsPolymers and Elastomers Testing

2026

A multifunctional graphene-integrated double-network nanocomposite hydrogel for dual strain-temperature wearable sensing

Romih A, Abdul Samad Y, Kim JK, Schiffer A

Advanced Composites and Hybrid Materials

UniVert

Adhesion TestingCompression TestingFatigue TestingTensile Testing

Adhesives and Sealants TestingHydrogel Mechanical TestingMaterial Fatigue and DurabilityStimuli Responsive Hydrogels CharacterizationWearable Bioelectronics

2026

Contact Sales

Product of Interest:
CellScale hexagon shapes